Diễn đàn đan móc
Bạn có muốn phản ứng với tin nhắn này? Vui lòng đăng ký diễn đàn trong một vài cú nhấp chuột hoặc đăng nhập để tiếp tục.
Diễn đàn đan móc

Diễn đàn dành cho các bạn thích đan móc


You are not connected. Please login or register

Xem chủ đề cũ hơn Xem chủ đề mới hơn Go down  Thông điệp [Trang 1 trong tổng số 1 trang]

1Giúp e gấp với ạ Empty Giúp e gấp với ạ 22/1/2013, 23:01

m0sh1n0


Cuộn len nhỏ
Cuộn len nhỏ
Giúp e dịch đoạn chart này với ạ

Cast on 54 stitches using long-tail cast on.

Rows 1-7: k3, *k1, p1, rep to last 3 sts, k3.

Row 8 (Cable row 1): k3, (k1, p1) 8 times, C16F, (k1, p1) 8 times, k3.

Rows 9-15: k3, *k1, p1, rep to last 3 sts, k3.

Row 16: (Cable row 2): k3, C16F, (k1, p1) 8 times, C16F, k3.

*C16F: Put next 8 stitches on cable needle and hold to front of work; (k1, p1) 4x, then (k1, p1) 4x from cable needle

E xin cảm ơn

2Giúp e gấp với ạ Empty Re: Giúp e gấp với ạ 22/1/2013, 23:05

m0sh1n0


Cuộn len nhỏ
Cuộn len nhỏ
Đây là nguyên văn bài của nó

An easy, totally reversible cabled scarf that will eat up a lot of yarn, lie flat and look fabulous on you!

Based on Vogue Stitchionary Vol 2 (cables). I used the Reversible Rib Cable, and made it smaller.

Manitou Passage Scarf

3 skeins Cascade 220 wool or any yarn that knits to 4 stitches per inch; cable needle; #7 needles or the size that gives you 4 spi in stocking stitch. Warning: this pattern is a *serious* yarn-eater. Plan accordingly!

Makes a scarf 6″ wide and as long as you like. (I did 14 repeats of the pattern for a 72″ long scarf. The cables are fat and thick and need more length to balance them out. Bundley-uppey!)

C16F: Put next 8 stitches on cable needle and hold to front of work; (k1, p1) 4x, then (k1, p1) 4x from cable needle. (Personally I had great difficulty trying to do ribbed cables with no cable needle, and don’t recommend it.)

Cast on 54 stitches using long-tail cast on.

Rows 1-7: k3, *k1, p1, rep to last 3 sts, k3.

Row 8 (Cable row 1): k3, (k1, p1) 8 times, C16F, (k1, p1) 8 times, k3.

Rows 9-15: k3, *k1, p1, rep to last 3 sts, k3.

Row 16: (Cable row 2): k3, C16F, (k1, p1) 8 times, C16F, k3.

Repeat these 16 rows for pattern, alternating Cable rows 1 and 2 so that each cable is vertically 16 stitches high, but alternate cables happen every 8 rows. The rest of the rows are worked in 1×1 ribbing, with three edge stitches on each side worked in garter stitch (knit every row).

The cables will gape a little more than you are used to – you can basically put a finger in behind them. Don’t worry about it! For a while I fiddled with the stitches to get everything to even out, but it really truly doesn’t improve the look of the scarf. They won’t show.

When the scarf is as long as you like end your cabling by knitting one last Cable Row 1, knit 8 more rows in the ribbing pattern and cast off loosely, but not too loosely because you don’t want your end to flare too much. Either side is fine; the scarf is totally reversible.

3Giúp e gấp với ạ Empty Re: Giúp e gấp với ạ 23/1/2013, 13:07

storm0flove

storm0flove
Cuộn len khá to
Cuộn len khá to
Giúp e gấp với ạ 392001758_935740e798

Lấy 54 mũi kiểu sợi-dài (long-tail cast on):


Dòng 1-7: 3 xuống, *1 xuống, 1 lên, lặp lại * cho tới 3 mũi cuối cùng, 3 xuống.

Dòng 8 (vặn thừng dòng 1): 3 xuống, (1 xuống, 1 lên) 8 lần, C16F, (1 xuống, 1 lên) 8 lần, 3 xuống.

Dòng 9-15: 3 xuống, *1 xuống, 1 lên, lặp lại * tới 3 mũi cuối, 3 xuống.

Dòng 16: (vặn thừng dòng 2): 3 xuống, C16F, (1 xuống, 1 lên) 8 lần, C16F, 3 xuống.

*C16F: Lấy 8 mũi kế tiếp sang que đan 2 đầu và đưa về mặt trước; (1 xuống, 1 lên) 4 lần, sau đó (1 xuống, 1 lên) 4 lần với các mũi trên que đan 2 đầu.

Tham khảo trong video clip là C4F:

Sponsored content


Xem chủ đề cũ hơn Xem chủ đề mới hơn Về Đầu Trang  Thông điệp [Trang 1 trong tổng số 1 trang]

Permissions in this forum:
Bạn không có quyền trả lời bài viết

 

Free forum | ©phpBB | Free forum support | Báo cáo lạm dụng | Thảo luận mới nhất